• <source id="eiquc"></source>
    <li id="eiquc"></li>
  • <kbd id="eiquc"><noscript id="eiquc"></noscript></kbd>
  • <blockquote id="eiquc"><noscript id="eiquc"></noscript></blockquote>
  • KMT 6V
    All-in-One Turret Milling Machine

    Overview

    The new all-in-one KMT-6V is a welcome addition to Kingston’s celebrated line of KMT manual turret mills. This fully outfitted milling machine includes special features such as X- and Y-axis power feeds controlled by a Yaskawa frequency inverter drive, longer 54” table, motorized Z-axis auto-knee with rapid function, auto-lubrication, cooling pump & system, coolant & chip pan, halogen worklight, and convenient control box (complete with E-stop button) in order to manage all of the features listed above. The KMT-6V also features a rugged 5 HP motor and a spindle with a Class 7 precision bearing and NT#40 nose—with speeds up to 4,200 RPM and a maximum runout of .0002 inches. The knee and table ways are hardened and ground, while a heavy-duty saddle support runs the full width of the table for extra stability. Kingston’s KMT-6V is strong, reliable, and accessorized.

    KMT 6V Special Features

    • X & Y-Axis Clutch-Type Auto-Feeds Controlled by Yaskawa Frequency Inverter Drive (180 Parameters)
    • 1HP Elevating Motor (Auto-Knee)
    • Coolant Pump & System
    • Convenient Multi-Function Control Box w/ E-Stop & Special Features Listed Above
    • 10” x 54” Table
    • Auto-Lubrication System (2 Switches)
    • Coolant & Chip Pan
    • Halogen Work Light
    • Simultaneous X & Z-Axis or Y & Z-Axis Movement Possible

    Other Standard Features

    • Main Motor: 5HP, 220V only, 3 Phase, 60 Cycle Main
    • NT#40 Spindle Nose
    • Class 7 Spindle bearings
    • Variable speed change (60 – 4200 RPM)
    • Chromed Quill
    • 3 Quill Feeds Up & Down With Auto Stops
    • Max Spindle Accuracy Within .0002” (.0051mm)
    • 10” x 54” Hardened & Ground Table
    • Square Ways in Both Y & Z Directions
    • Hardened & Ground Back Gear & Clutch
    • Double Nuts Backlash Eliminator On X+Y Axes
    • Double Lock for Table and Knee
    • Adjusting Tool & Tool Box

    Optional Accessories

    • A & T Mechanical Power Lock Drawbar
    • Yaskawa Frequency Inverter Drive (Factory Installation Only)
    • 2-Axis or 3-Axis Digital Readout (DRO)

     

    Capacity  
    Table 10" x 54"
    Travel (X x Y) 34.4" x 15.7"
    Travel (Z) Quill 5.0"
    Travel (Z) Knee 17.5"

     

    Spindle  
    Spindle Motor 5HP
    Spindle Taper NT#40
    Spindle Speed 60 – 4200 RPM
    Spindle Power Feed Rate (3 Speeds) 0.0015"/Rev, 0.003"/Rev, 0.006"/Rev
    Quill Diameter 4.1"

     

    Feeds  
    X- & Y-Axis Feeds 0 – 1730 RPM
    Z-Axis (Knee) Feed  0 – 560 RPM
    X / Y / Z Motors 1/2 / 1/2 / 1 HP

     

    Dimensions  
    Overall Height 93.7"
    Overall Length 60.3"
    Overall Width 74.8"
    Weight 3,740 lbs

     

     

     

     

     

    天天斗牛下载